Description

WiFi Wieless RF Smart Home: Input Voltage : AC 90-250V Max Current : 10A Wireless Type : Wifi 2.4GHz Wireless standard : IEEE 802 .11 b/g/n Remote ON/OFF: Turn electrical devices on/off from anywhere App Support: Free iOS and Android mobile App "Smart Life" Sync Status: Real-time device status provided to App Timing: Set scheduled/countdown/loop timers to turn on/off at specified time Share Control: Control your smart home together with your family Scene: Turn on/off a gang of devices with one tap Voice Control: Works perfectly with Amazon Alexa,Google Home,IFTTT Wall Panel Transmitter: Operating Frequency: 433MHz Battery Model: CR2032 (Package Not includedbattery) Dimensions: 86mm x 86mm x 13mm Distance: indoor (20 meters) outdoor (80 meters) How to install this smart switch: You don't need to open the outer casing of this smart switch You can wire directly to the terminal block Please note: Please turn off the power before wiring. Please connect the wires according to the following diagram WIRING DIAGRAM After the wiring is completed, turn on the power and operate according to the status of the smart switch indicator: 1) If the red light of the smart switch flashes continuously at this time, it indicates that the smart switch has entered the state of waiting for connection to WiFi; then open the APP and follow the instructions to connect to WiFi. 2) If the indicator light of the smart switch is not flashing red light, please press the button of the smart switch and keep it for more than 5 seconds until the red light flashes continuously, then open the APP and connect to the WiFi according to the manual. Scan the QR-code of the manual or Search ‘ Smart Life ’ to download and install the device's APP How to match smart switch with 433Mhz RF remote control? This Smart Switch only can link WIFI Then can match RF 433Mhz Remote Control. This smart switch has 3 working modes to match the 433Mhz RF remote: (smart switch, hereinafter referred to as: receiver) About receiver's Working Mode: Manual On/Off: Press the receiver's Learning button, the receiver's relay is ON; press button again, the receiver's relay is OFF. Momentary mode: Press the Remote control button, the receiver's relay is ON; release button, the receiver's relay is OFF. Toggle mode: Press Remote control button for 1 time, the receiver's relay is ON; press button again, the receiver's relay is OFF. Latched mode: Press Remote control button A, the receiver's relay is ON, Press the transmitter's button B, the receiver's relay is OFF. Setting power-OFF memory: When the power of the receiver is disconnected, the status before the power disconnection of the receiver will be recorded. When the power is restored, the receiver will return to the status before the power disconnection. (For example: before the power is disconnected, the receiver is off, and the receiver will remain off after the power is restored; Before the power is disconnected, the receiver is turned on, and the receiver will automatically turn on when the power is restored. ) Reset function: After push the receiver's learning button 8 times, the receiver Clear all the remote control data in its memory. When the red LED flashes for a few times, it indicates that the clear function is completed. (After cleared the code in the receiver, all the remote control cannot work with the receiver.) Matching method: 1.Manual On/Off: Press the receiver's Learning button 1 time,The receiver will turn on the relay and the circuit will be connected. Press the receiver's Learning button again,The receiver will disconnect the relay and disconnect the circuit. 2. Setting Toggle Mode (Common working mode): Press the receiver's Learning button 2 time, the receiver's red LED will be lights up, it comes into Setting state; Press the remote's button, the receiver's red LED will flash then come off, Setting successfully. 3. Setting Latched Mode: (Note: When you choose "Latched Mode", you need to setting two different buttons on the Remote control, the first time learn is for “ON”, the second time learn for “OFF”. For example: button A = ON, button B = OFF) Press the receiver's Learning button 3 time, the receiver's red LED will be lights up, it comes into Setting state; Press the remote's A button, the receiver's red LED will flash and then remains lit; Then press the remote's B button, the receiver's red LED will flash then come off, Setting successfully. 4. Setting momentary Mode: Press the receiver's Learning button 4 time, the receiver's red LED will be lights up, it comes into Setting state; Press the remote's button, the receiver's red LED will flash then come off, Setting successfully. 5. Setting power-off memory Press the receiver's Learning button 6 time, the receiver's red LED will be Flashing,the relay will energises the circuit.The setting is completed. Note: A Smart Switch can only store 12 buttons (on the remote). Saved button number of more than 12, it will cause all of the stored remote control cannot control the Smart Switch. You need reboot the power and reset the RF remote control settings (press the Smart Switch's matching button 8 times) Note: A Smart Switch can only store 12 buttons (on the remote). Saved button number of more than 12, it will cause all of the stored remote control cannot control the Smart Switch. You need reboot the power and reset the RF remote control settings (press the Smart Switch's matching button 8 times)