Description

Feature Products ESP8266 WIFI 1/2/4 Channel 30A Relay ESP-12F Development Board DC 5V 7V-80V Single channel DC7-80/5V I. Overview ESP8266 single-channel 30A relay development board is equipped with ESP-12F WiFi module, all I/O ports are led out, and it supports DC7-80V/5V power supply. Provide Arduino development environment reference code, suitable for ESP8266 secondary development learning, smart home wireless control and other occasions. 2. Features 1. On-board mature and stable ESP-12F WiFi module, large capacity 4M Byte Flash; 2. The I/O port and UART program download port of the WiFi module are all led out, which is convenient for secondary development; 3. The power supply mode supports DC7-80V/5V; 4. Onboard WiFi module RST reset button and a programmable button; 5. ESP-12F supports the use of development tools such as Eclipse/Arduino IDE, and provides reference programs under the Arduino development environment; 6. Onboard 1 way 5V/30A relay, output switch signal, suitable for controlling load within AC 250V/DC30V; 7. Onboard power indicator and relay indicator, ESP-12F comes with 1 programmable LED. 3. Hardware introduction and description 1. Board size: 78*47mm Weight: 45g 3. Interface introduction Programming port: ESP8266's GND, RX, TX, 5V are respectively connected to the GND, TX, RX, 5V of the external TTL serial port module. IO0 needs to be connected to GND when downloading, and then disconnect the connection between IO0 and GND after the download is complete; Relay output: NC: Normally closed, the relay is short-connected with COM before the pull-in, and hangs in the air after pull-in; COM: public end; NO: Normally open end, the relay is suspended before being closed, and shorted to COM after being closed. 4. Introduction to GPIO port Serial number name Function Description Serial number name Function Description 1 ADC A/D conversion result. Input voltage range: 0～1V, value range: 0～1024 10 IO2 GPIO2; UART1_TXD 2 EN Enable pin, pull up by default 11 IO15 GPIO15; MTDO; HSPI_CS; UART0_RTS 3 IO16 GPIO16 12 TXD UART0_TXD; GPIO1 4 IO14 GPIO14; HSPI_CLK 13 RXD UART0_RXD; GPIO3 5 IO12 GPIO12; HSPI_MISO 14 GND Power ground 6 IO13 GPIO13; HSPI_MOSI; UART0_CTS 15 5V 5V power supply 7 IO5 GPIO5 16 3.3V 3.3V power supply 8 IO4 GPIO4 17 RY1 Relay drive port, you can use short-circuit cap and IO16 to short-circuit; if you want to use other I/O drive relay, you can use DuPont wire jumper 9 IO0 GPIO0 Dual channel DC7-28/5V I. Overview The ESP8266 dual 30A relay development board is equipped with ESP-12F WiFi module, all I/O ports are led out, and it supports DC7-28V/5V power supply. Provide Arduino development environment reference code, suitable for ESP8266 secondary development learning, smart home wireless control and other occasions. 2. Features 1. On-board mature and stable ESP-12F WiFi module, large capacity 4M Byte Flash; 2. The I/O port and UART program download port of the WiFi module are all led out, which is convenient for secondary development; 3. The power supply mode supports DC7-28V/5V; 4. Onboard WiFi module RST reset button and a programmable button; 5. ESP-12F supports the use of development tools such as Eclipse/Arduino IDE, and provides reference programs under the Arduino development environment; 6. Onboard 2 5V/30A relays, output switch signals, suitable for controlling loads whose working voltage is within AC 250V/DC30V; 7. On-board power indicator, relay indicator and 1 programmable LED. 3. Hardware introduction and description Board size: 83*68mm Weight: 85g 4.Interface introduction Programming port: ESP8266's GND, RX, TX, 5V are respectively connected to the GND, TX, RX, 5V of the external TTL serial port module. IO0 needs to be connected to GND when downloading, and then disconnect the connection between IO0 and GND after the download is complete; Relay output: NC: Normally closed, the relay is short-connected with COM before the pull-in, and hangs in the air after pull-in; COM: public end; NO: Normally open end, the relay is suspended before being closed, and shorted to COM after being closed. 5. Introduction to GPIO port Serial number name Function Description Serial number name Function Description 1 ADC A/D conversion result. Input voltage range: 0～1V, value range: 0～1024 10 IO2 GPIO2; UART1_TXD 2 EN Enable pin, pull up by default 11 IO15 GPIO15; MTDO; HSPI_CS; UART0_RTS 3 IO16 GPIO16 12 TXD UART0_TXD; GPIO1 4 IO14 GPIO14; HSPI_CLK 13 RXD UART0_RXD; GPIO3 5 IO12 GPIO12; HSPI_MISO 14 GND Power ground 6 IO13 GPIO13; HSPI_MOSI; UART0_CTS 15 5V 5V power supply 7 IO5 GPIO5 16 3.3V 3.3V power supply 8 IO4 GPIO4 17 RY1 The first relay drive port can be short-circuited with IO16 using a shorting cap; if you want to use other I/O drive relays, you can use DuPont wire jumpers 9 IO0 GPIO0 18 RY2 For the second relay drive port, you can use a shorting cap and IO14 to short; if you want to use other I/O drive relays, you can use DuPont wire jumpers 4 Channel DC7-28V/5V Features: The Esp8266 four-way 30A relay development board is equipped with an esp-12f WiFi module, the I / O ports are all led, and it supports dc7-28v / 5V power supply mode. It is suitable for esp8266 secondary development and learning, smart home wireless control and other occasions. 1. Mature and stable esp-12f WiFi module on board, large capacity 4m Byte Flash. 2. The WiFi module I / O port and UART program download port are all led,It is suitable for secondary development. One 3. The power supply mode supports dc7-28v / 5V. 4. Integrated WiFi module RST Reset button and a programmable key. 5. Esp-12f supports the use of eclipse / Arduino LDE and other developers Provides the reference program in the Arduino development environment. 6. Onboard 5V / 30A 4-way relay, output switch signal, suitable for control.Control the load whose working voltage is Within AC 250V / DC 30V. 7. On-board power indicator, 1 programmable led and relay indicator. 8. Board size: 122.5x87mm Weight: 160g GND, Rx, TX and 5V of esp8266 record and write port are respectively connected with GND, TX, RX and 5V of external TTL serial port module. When downloading, 00 needs to be connected with GND, and then disconnect 00 from GND after downloading. NC relay output: normally closed end, the relay is shorted to com before closing and suspended after closing. COM: public end. No: normal start, the relay is suspended before closing and will short to com after closing. Shipping Policy Item Location Payment Mathord Returns Policy About Feedback Shipping Policy 1. We Ship to Worldwide 2. We ship your orders within 1-2 business days after the payment cleared. 3. Item shipped from China via china Post Airmail, reach most of the countries within 2 to 4 weeks. 4. Delivery time depends on destination and other factors, it may takes up to 20 days. If you don't receive the item after 30 days,please keep in touch with us, we'll investigate and solve the delivery problem. 5. Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. Item Location ShenZhen Payment Mathord 1. We accept PAYPAL only. 2. Payment must be made within 7 days of auction closing (Unpaid dispute will automatically open when item is not paid in 7 days). 3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES. 4. Please list your special requests (color, packages, value of declaration, etc.) in the EBAY NOTES SECTION when you make payment Returns Policy 1. Customer satisfaction is our top goal. All products are quality checked. They are new and in good condition when shipped to our customers. If product is defective or damage upon arrival, or wrong product shipped, please keep in touch with us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer. 2. Please keep in touch with us first if you have anyproblems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner. 3. We appreciate your Positive Feedback, and will do the same in return. PLEASE DO NOT leave negative feedback without first communication with us. Please allow max 24 HOURS for us to respond About Feedback We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.It is impossible to address issues if we do not know about them!